Discussion:
Where is Bluetooth installation coming from and how can I remove it from my old Debian box?
(too old to reply)
Ant
2010-02-23 14:29:33 UTC
Permalink
Hello.

I noticed my old Debian box, with Kernel v2.6.30-2-686 #1 SMP Fri Dec 4
00:53:20 UTC 2009 i686 GNU/Linux, has Bluetooth installed and running.
Is that part of the kernel or somewhere else? Dmesg command showed:

$ dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.30-2-686 (Debian 2.6.30-8squeeze1)
(***@debian.org) (gcc version 4.3.4 (Debian 4.3.4-6) ) #1 SMP Fri Dec
4 00:53:20 UTC 2009
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
[ 0.000000] BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000009fff0000 (usable)
[ 0.000000] BIOS-e820: 000000009fff0000 - 000000009fff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000009fff3000 - 00000000a0000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] DMI 2.3 present.
[ 0.000000] Phoenix BIOS detected: BIOS may corrupt low RAM, working
around it.
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000
(usable) ==> (reserved)
[ 0.000000] last_pfn = 0x9fff0 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-C7FFF write-protect
[ 0.000000] C8000-FFFFF uncachable
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask FF80000000 write-back
[ 0.000000] 1 base 0080000000 mask FFE0000000 write-back
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new
0x7010600070106
[ 0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 0037400000 page 2M
[ 0.000000] 0037400000 - 00377fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 377fe000 @ 10000-15000
[ 0.000000] RAMDISK: 3768f000 - 37fefb3c
[ 0.000000] Allocated new RAMDISK: 00543000 - 00ea3b3c
[ 0.000000] Move RAMDISK from 000000003768f000 - 0000000037fefb3b to
00543000 - 00ea3b3b
[ 0.000000] ACPI: RSDP 000f9260 00014 (v00 Nvidia)
[ 0.000000] ACPI: RSDT 9fff3040 00030 (v01 Nvidia AWRDACPI 42302E31
AWRD 00000000)
[ 0.000000] ACPI: FACP 9fff30c0 00074 (v01 Nvidia AWRDACPI 42302E31
AWRD 00000000)
[ 0.000000] ACPI: DSDT 9fff3180 063C4 (v01 NVIDIA AWRDACPI 00001000
MSFT 0100000E)
[ 0.000000] ACPI: FACS 9fff0000 00040
[ 0.000000] ACPI: MCFG 9fff9680 0003C (v01 Nvidia AWRDACPI 42302E31
AWRD 00000000)
[ 0.000000] ACPI: APIC 9fff95c0 00072 (v01 Nvidia AWRDACPI 42302E31
AWRD 00000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 1671MB HIGHMEM available.
[ 0.000000] 887MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 377fe000
[ 0.000000] low ram: 0 - 377fe000
[ 0.000000] node 0 low ram: 00000000 - 377fe000
[ 0.000000] node 0 bootmap 00011000 - 00017f00
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 00377fe000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==>
[0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==>
[0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==>
[0000006000 - 0000007000]
[ 0.000000] #3 [0000100000 - 000053fb10] TEXT DATA BSS ==>
[0000100000 - 000053fb10]
[ 0.000000] #4 [000009f400 - 0000100000] BIOS reserved ==>
[000009f400 - 0000100000]
[ 0.000000] #5 [0000540000 - 00005420ae] BRK ==>
[0000540000 - 00005420ae]
[ 0.000000] #6 [0000010000 - 0000011000] PGTABLE ==>
[0000010000 - 0000011000]
[ 0.000000] #7 [0000543000 - 0000ea3b3c] NEW RAMDISK ==>
[0000543000 - 0000ea3b3c]
[ 0.000000] #8 [0000011000 - 0000018000] BOOTMAP ==>
[0000011000 - 0000018000]
[ 0.000000] found SMP MP-table at [c00f5380] f5380
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000377fe
[ 0.000000] HighMem 0x000377fe -> 0x0009fff0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0009fff0
[ 0.000000] On node 0 totalpages: 655231
[ 0.000000] free_area_init_node: node 0, pgdat c0408d40, node_mem_map
c1000200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 1744 pages used for memmap
[ 0.000000] Normal zone: 221486 pages, LIFO batch:31
[ 0.000000] HighMem zone: 3344 pages used for memmap
[ 0.000000] HighMem zone: 424674 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.
[ 0.000000] If you got timer trouble try acpi_use_timer_override
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI
0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ14 used by override.
[ 0.000000] ACPI: IRQ15 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009f000 -
00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 -
00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 -
0000000000100000
[ 0.000000] Allocating PCI resources starting at a4000000 (gap:
a0000000:40000000)
[ 0.000000] NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 11 pages at c240a000, static data 22172
bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 650111
[ 0.000000] Kernel command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.30-2-686
root=UUID=fe4a1af1-1979-49fb-9668-314a24b12890 ro quiet
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] NR_IRQS:1280
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2411.146 MHz processor.
[ 0.004000] spurious 8259A interrupt: IRQ7.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288
bytes)
[ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.004000] Initializing HighMem for node 0 (000377fe:0009fff0)
[ 0.004000] Memory: 2584684k/2621376k available (2174k kernel code,
35396k reserved, 1138k data, 320k init, 1712072k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xffe16000 - 0xfffff000 (1956 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
[ 0.004000] .init : 0xc0444000 - 0xc0494000 ( 320 kB)
[ 0.004000] .data : 0xc031f865 - 0xc043c2f0 (1138 kB)
[ 0.004000] .text : 0xc0100000 - 0xc031f865 (2174 kB)
[ 0.004000] Checking if this processor honours the WP bit even in
supervisor mode...Ok.
[ 0.004015] Calibrating delay loop (skipped), value calculated using
timer frequency.. 4822.29 BogoMIPS (lpj=9644584)
[ 0.004065] Security Framework initialized
[ 0.004075] SELinux: Disabled at boot.
[ 0.004092] Mount-cache hash table entries: 512
[ 0.004253] Initializing cgroup subsys ns
[ 0.004258] Initializing cgroup subsys cpuacct
[ 0.004262] Initializing cgroup subsys devices
[ 0.004265] Initializing cgroup subsys freezer
[ 0.004267] Initializing cgroup subsys net_cls
[ 0.004290] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
[ 0.004292] CPU: L2 Cache: 512K (64 bytes/line)
[ 0.004294] CPU: Physical Processor ID: 0
[ 0.004295] CPU: Processor Core ID: 0
[ 0.004301] Intel machine check architecture supported.
[ 0.004303] Intel machine check reporting enabled on CPU#0.
[ 0.004320] Checking 'hlt' instruction... OK.
[ 0.020867] ACPI: Core revision 20090320
[ 0.032575] ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
[ 0.072846] CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 4600+
stepping 01
[ 0.076001] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.004000] Initializing CPU#1
[ 0.004000] Calibrating delay using timer specific routine.. 4822.54
BogoMIPS (lpj=9645090)
[ 0.004000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
[ 0.004000] CPU: L2 Cache: 512K (64 bytes/line)
[ 0.004000] CPU: Physical Processor ID: 0
[ 0.004000] CPU: Processor Core ID: 1
[ 0.004000] Intel machine check architecture supported.
[ 0.004000] Intel machine check reporting enabled on CPU#1.
[ 0.004000] x86 PAT enabled: cpu 1, old 0x7040600070406, new
0x7010600070106
[ 0.160606] CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 4600+
stepping 01
[ 0.160745] Brought up 2 CPUs
[ 0.160748] Total of 2 processors activated (9644.83 BogoMIPS).
[ 0.160804] CPU0 attaching sched-domain:
[ 0.160807] domain 0: span 0-1 level MC
[ 0.160809] groups: 0 1
[ 0.160814] CPU1 attaching sched-domain:
[ 0.160816] domain 0: span 0-1 level MC
[ 0.160818] groups: 1 0
[ 0.160882] net_namespace: 1088 bytes
[ 0.160882] Booting paravirtualized kernel on bare hardware
[ 0.160882] regulator: core version 0.5
[ 0.160882] NET: Registered protocol family 16
[ 0.160882] ACPI: bus type pci registered
[ 0.160882] PCI: MCFG configuration 0: base e0000000 segment 0 buses
0 - 255
[ 0.160882] PCI: MCFG area at e0000000 reserved in E820
[ 0.160882] PCI: Using MMCONFIG for extended config space
[ 0.160882] PCI: Using configuration type 1 for base access
[ 0.160882] bio: create slab <bio-0> at 0
[ 0.164048] ACPI: EC: Look up EC in DSDT
[ 0.171556] ACPI: Interpreter enabled
[ 0.171563] ACPI: (supports S0 S1 S4 S5)
[ 0.171585] ACPI: Using IOAPIC for interrupt routing
[ 0.180172] ACPI: No dock devices found.
[ 0.180186] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.180216] HPET not enabled in BIOS. You might try hpet=force boot
option
[ 0.180216] pci 0000:00:01.1: reg 10 io port: [0xfc00-0xfc1f]
[ 0.180216] pci 0000:00:01.1: reg 20 io port: [0x4c00-0x4c3f]
[ 0.180216] pci 0000:00:01.1: reg 24 io port: [0x4c40-0x4c7f]
[ 0.180216] pci 0000:00:01.1: PME# supported from D3hot D3cold
[ 0.180216] pci 0000:00:01.1: PME# disabled
[ 0.180216] pci 0000:00:02.0: reg 10 32bit mmio: [0xfe02f000-0xfe02ffff]
[ 0.180216] pci 0000:00:02.0: supports D1 D2
[ 0.180216] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.180216] pci 0000:00:02.0: PME# disabled
[ 0.180216] pci 0000:00:02.1: reg 10 32bit mmio: [0xfeb00000-0xfeb000ff]
[ 0.180216] pci 0000:00:02.1: supports D1 D2
[ 0.180216] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.180216] pci 0000:00:02.1: PME# disabled
[ 0.180222] pci 0000:00:04.0: reg 10 io port: [0xf000-0xf0ff]
[ 0.180226] pci 0000:00:04.0: reg 14 io port: [0xec00-0xecff]
[ 0.180230] pci 0000:00:04.0: reg 18 32bit mmio: [0xfe02d000-0xfe02dfff]
[ 0.180242] pci 0000:00:04.0: supports D1 D2
[ 0.180262] pci 0000:00:06.0: reg 20 io port: [0xe000-0xe00f]
[ 0.180284] pci 0000:00:07.0: reg 10 io port: [0x9f0-0x9f7]
[ 0.180288] pci 0000:00:07.0: reg 14 io port: [0xbf0-0xbf3]
[ 0.180292] pci 0000:00:07.0: reg 18 io port: [0x970-0x977]
[ 0.180295] pci 0000:00:07.0: reg 1c io port: [0xb70-0xb73]
[ 0.180299] pci 0000:00:07.0: reg 20 io port: [0xcc00-0xcc0f]
[ 0.180303] pci 0000:00:07.0: reg 24 32bit mmio: [0xfe02b000-0xfe02bfff]
[ 0.180323] pci 0000:00:08.0: reg 10 io port: [0x9e0-0x9e7]
[ 0.180327] pci 0000:00:08.0: reg 14 io port: [0xbe0-0xbe3]
[ 0.180330] pci 0000:00:08.0: reg 18 io port: [0x960-0x967]
[ 0.180334] pci 0000:00:08.0: reg 1c io port: [0xb60-0xb63]
[ 0.180337] pci 0000:00:08.0: reg 20 io port: [0xb800-0xb80f]
[ 0.180341] pci 0000:00:08.0: reg 24 32bit mmio: [0xfe02a000-0xfe02afff]
[ 0.180374] pci 0000:00:0a.0: reg 10 32bit mmio: [0xfe029000-0xfe029fff]
[ 0.180377] pci 0000:00:0a.0: reg 14 io port: [0xb400-0xb407]
[ 0.180391] pci 0000:00:0a.0: supports D1 D2
[ 0.180393] pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.180396] pci 0000:00:0a.0: PME# disabled
[ 0.180423] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.180426] pci 0000:00:0b.0: PME# disabled
[ 0.180453] pci 0000:00:0c.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.180455] pci 0000:00:0c.0: PME# disabled
[ 0.180482] pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.180485] pci 0000:00:0d.0: PME# disabled
[ 0.180510] pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.180513] pci 0000:00:0e.0: PME# disabled
[ 0.180617] pci 0000:01:09.0: reg 10 32bit mmio: [0xfdeff000-0xfdefffff]
[ 0.180622] pci 0000:01:09.0: reg 14 io port: [0xac00-0xac3f]
[ 0.180627] pci 0000:01:09.0: reg 18 32bit mmio: [0xfdd00000-0xfddfffff]
[ 0.180639] pci 0000:01:09.0: reg 30 32bit mmio: [0x000000-0x0fffff]
[ 0.180650] pci 0000:01:09.0: supports D1 D2
[ 0.180652] pci 0000:01:09.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.180655] pci 0000:01:09.0: PME# disabled
[ 0.180674] pci 0000:00:09.0: transparent bridge
[ 0.180677] pci 0000:00:09.0: bridge io port: [0xa000-0xafff]
[ 0.180680] pci 0000:00:09.0: bridge 32bit mmio: [0xfdc00000-0xfdefffff]
[ 0.180683] pci 0000:00:09.0: bridge 32bit mmio pref:
[0xfdf00000-0xfdffffff]
[ 0.180712] pci 0000:00:0b.0: bridge io port: [0x9000-0x9fff]
[ 0.180714] pci 0000:00:0b.0: bridge 32bit mmio: [0xfdb00000-0xfdbfffff]
[ 0.180718] pci 0000:00:0b.0: bridge 64bit mmio pref:
[0xfda00000-0xfdafffff]
[ 0.180746] pci 0000:00:0c.0: bridge io port: [0x8000-0x8fff]
[ 0.180749] pci 0000:00:0c.0: bridge 32bit mmio: [0xfd900000-0xfd9fffff]
[ 0.180753] pci 0000:00:0c.0: bridge 64bit mmio pref:
[0xfd800000-0xfd8fffff]
[ 0.180781] pci 0000:00:0d.0: bridge io port: [0x7000-0x7fff]
[ 0.180784] pci 0000:00:0d.0: bridge 32bit mmio: [0xfd700000-0xfd7fffff]
[ 0.180787] pci 0000:00:0d.0: bridge 64bit mmio pref:
[0xfd600000-0xfd6fffff]
[ 0.180811] pci 0000:05:00.0: reg 10 32bit mmio: [0xfa000000-0xfaffffff]
[ 0.180818] pci 0000:05:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff]
[ 0.180825] pci 0000:05:00.0: reg 1c 64bit mmio: [0xf8000000-0xf9ffffff]
[ 0.180831] pci 0000:05:00.0: reg 24 io port: [0x6c00-0x6c7f]
[ 0.180836] pci 0000:05:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[ 0.180881] pci 0000:00:0e.0: bridge io port: [0x6000-0x6fff]
[ 0.180884] pci 0000:00:0e.0: bridge 32bit mmio: [0xf8000000-0xfbffffff]
[ 0.180888] pci 0000:00:0e.0: bridge 64bit mmio pref:
[0xd0000000-0xdfffffff]
[ 0.180897] pci_bus 0000:00: on NUMA node 0
[ 0.180903] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.181115] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 0.241143] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 11 12
14 15) *0, disabled.
[ 0.241143] ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 11 12
14 15) *0, disabled.
[ 0.241143] ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 *7 9 10 11 12
14 15)
[ 0.241143] ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 *5 7 9 10 11 12
14 15)
[ 0.241143] ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12
14 15) *0, disabled.
[ 0.241143] ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 *7 9 10 11 12
14 15)
[ 0.241157] ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12
14 15) *0, disabled.
[ 0.241327] ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 7 9 10 *11 12
14 15)
[ 0.241495] ACPI: PCI Interrupt Link [LACI] (IRQs *3 4 5 7 9 10 11 12
14 15)
[ 0.241664] ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 *10 11 12
14 15)
[ 0.241833] ACPI: PCI Interrupt Link [LSMB] (IRQs *3 4 5 7 9 10 11 12
14 15)
[ 0.242002] ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 *5 7 9 10 11 12
14 15)
[ 0.242170] ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12
14 15) *0, disabled.
[ 0.242349] ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 10 *11 12
14 15)
[ 0.242527] ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 7 9 *10 11 12
14 15)
[ 0.244126] ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12
14 15) *0, disabled.
[ 0.244317] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
[ 0.244501] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
[ 0.244684] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0
[ 0.244868] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0
[ 0.244988] ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
[ 0.245178] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
[ 0.245367] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0,
disabled.
[ 0.245556] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0
[ 0.245744] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0
[ 0.245933] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0
[ 0.246121] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
[ 0.246309] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
[ 0.246499] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0,
disabled.
[ 0.246696] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
[ 0.246893] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
[ 0.247089] ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0,
disabled.
[ 0.247147] PCI: Using ACPI for IRQ routing
[ 0.276004] pnp: PnP ACPI init
[ 0.276013] ACPI: bus type pnp registered
[ 0.280700] pnp 00:0c: mem resource (0xf0000-0xf3fff) overlaps
0000:01:09.0 BAR 6 (0x0-0xfffff), disabling
[ 0.280700] pnp 00:0c: mem resource (0xf4000-0xf7fff) overlaps
0000:01:09.0 BAR 6 (0x0-0xfffff), disabling
[ 0.280700] pnp 00:0c: mem resource (0xf8000-0xfbfff) overlaps
0000:01:09.0 BAR 6 (0x0-0xfffff), disabling
[ 0.280700] pnp 00:0c: mem resource (0xfc000-0xfffff) overlaps
0000:01:09.0 BAR 6 (0x0-0xfffff), disabling
[ 0.280700] pnp 00:0c: mem resource (0x0-0x9ffff) overlaps
0000:01:09.0 BAR 6 (0x0-0xfffff), disabling
[ 0.280700] pnp: PnP ACPI: found 13 devices
[ 0.280700] ACPI: ACPI bus type pnp unregistered
[ 0.280700] PnPBIOS: Disabled by ACPI PNP
[ 0.280700] system 00:01: ioport range 0x4000-0x407f has been reserved
[ 0.280700] system 00:01: ioport range 0x4080-0x40ff has been reserved
[ 0.280700] system 00:01: ioport range 0x4400-0x447f has been reserved
[ 0.280700] system 00:01: ioport range 0x4480-0x44ff has been reserved
[ 0.280700] system 00:01: ioport range 0x4800-0x487f has been reserved
[ 0.280700] system 00:01: ioport range 0x4880-0x48ff has been reserved
[ 0.280700] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[ 0.280700] system 00:02: ioport range 0x290-0x29e has been reserved
[ 0.280700] system 00:0b: iomem range 0xe0000000-0xefffffff has been
reserved
[ 0.280700] system 00:0c: iomem range 0x9fff0000-0x9fffffff could not
be reserved
[ 0.280700] system 00:0c: iomem range 0xffff0000-0xffffffff has been
reserved
[ 0.280700] system 00:0c: iomem range 0x100000-0x9ffeffff could not
be reserved
[ 0.280700] system 00:0c: iomem range 0xfec00000-0xfec00fff could not
be reserved
[ 0.280700] system 00:0c: iomem range 0xfee00000-0xfeefffff has been
reserved
[ 0.280700] system 00:0c: iomem range 0xfefff000-0xfeffffff has been
reserved
[ 0.280700] system 00:0c: iomem range 0xfff80000-0xfff80fff has been
reserved
[ 0.280700] system 00:0c: iomem range 0xfff90000-0xfffbffff has been
reserved
[ 0.280700] system 00:0c: iomem range 0xfffed000-0xfffeffff has been
reserved
[ 0.316240] pci 0000:00:09.0: PCI bridge, secondary bus 0000:01
[ 0.316242] pci 0000:00:09.0: IO window: 0xa000-0xafff
[ 0.316246] pci 0000:00:09.0: MEM window: 0xfdc00000-0xfdefffff
[ 0.316250] pci 0000:00:09.0: PREFETCH window:
0x000000fdf00000-0x000000fdffffff
[ 0.316253] pci 0000:00:0b.0: PCI bridge, secondary bus 0000:02
[ 0.316256] pci 0000:00:0b.0: IO window: 0x9000-0x9fff
[ 0.316259] pci 0000:00:0b.0: MEM window: 0xfdb00000-0xfdbfffff
[ 0.316261] pci 0000:00:0b.0: PREFETCH window:
0x000000fda00000-0x000000fdafffff
[ 0.316265] pci 0000:00:0c.0: PCI bridge, secondary bus 0000:03
[ 0.316267] pci 0000:00:0c.0: IO window: 0x8000-0x8fff
[ 0.316270] pci 0000:00:0c.0: MEM window: 0xfd900000-0xfd9fffff
[ 0.316273] pci 0000:00:0c.0: PREFETCH window:
0x000000fd800000-0x000000fd8fffff
[ 0.316277] pci 0000:00:0d.0: PCI bridge, secondary bus 0000:04
[ 0.316279] pci 0000:00:0d.0: IO window: 0x7000-0x7fff
[ 0.316282] pci 0000:00:0d.0: MEM window: 0xfd700000-0xfd7fffff
[ 0.316285] pci 0000:00:0d.0: PREFETCH window:
0x000000fd600000-0x000000fd6fffff
[ 0.316290] pci 0000:00:0e.0: PCI bridge, secondary bus 0000:05
[ 0.316292] pci 0000:00:0e.0: IO window: 0x6000-0x6fff
[ 0.316295] pci 0000:00:0e.0: MEM window: 0xf8000000-0xfbffffff
[ 0.316298] pci 0000:00:0e.0: PREFETCH window:
0x000000d0000000-0x000000dfffffff
[ 0.316306] pci 0000:00:09.0: setting latency timer to 64
[ 0.316311] pci 0000:00:0b.0: setting latency timer to 64
[ 0.316315] pci 0000:00:0c.0: setting latency timer to 64
[ 0.316319] pci 0000:00:0d.0: setting latency timer to 64
[ 0.316323] pci 0000:00:0e.0: setting latency timer to 64
[ 0.316327] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.316329] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.316332] pci_bus 0000:01: resource 0 io: [0xa000-0xafff]
[ 0.316335] pci_bus 0000:01: resource 1 mem: [0xfdc00000-0xfdefffff]
[ 0.316337] pci_bus 0000:01: resource 2 pref mem [0xfdf00000-0xfdffffff]
[ 0.316340] pci_bus 0000:01: resource 3 io: [0x00-0xffff]
[ 0.316342] pci_bus 0000:01: resource 4 mem: [0x000000-0xffffffff]
[ 0.316345] pci_bus 0000:02: resource 0 io: [0x9000-0x9fff]
[ 0.316347] pci_bus 0000:02: resource 1 mem: [0xfdb00000-0xfdbfffff]
[ 0.316350] pci_bus 0000:02: resource 2 pref mem [0xfda00000-0xfdafffff]
[ 0.316353] pci_bus 0000:03: resource 0 io: [0x8000-0x8fff]
[ 0.316355] pci_bus 0000:03: resource 1 mem: [0xfd900000-0xfd9fffff]
[ 0.316357] pci_bus 0000:03: resource 2 pref mem [0xfd800000-0xfd8fffff]
[ 0.316360] pci_bus 0000:04: resource 0 io: [0x7000-0x7fff]
[ 0.316363] pci_bus 0000:04: resource 1 mem: [0xfd700000-0xfd7fffff]
[ 0.316365] pci_bus 0000:04: resource 2 pref mem [0xfd600000-0xfd6fffff]
[ 0.316368] pci_bus 0000:05: resource 0 io: [0x6000-0x6fff]
[ 0.316371] pci_bus 0000:05: resource 1 mem: [0xf8000000-0xfbffffff]
[ 0.316373] pci_bus 0000:05: resource 2 pref mem [0xd0000000-0xdfffffff]
[ 0.316447] NET: Registered protocol family 2
[ 0.320017] Switched to high resolution mode on CPU 0
[ 0.320761] Switched to high resolution mode on CPU 1
[ 0.364103] IP route cache hash table entries: 32768 (order: 5,
131072 bytes)
[ 0.364619] TCP established hash table entries: 131072 (order: 8,
1048576 bytes)
[ 0.366192] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.366973] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.366977] TCP reno registered
[ 0.376152] NET: Registered protocol family 1
[ 0.376228] Trying to unpack rootfs image as initramfs...
[ 0.633599] Freeing initrd memory: 9602k freed
[ 0.649503] audit: initializing netlink socket (disabled)
[ 0.649527] type=2000 audit(1266904252.648:1): initialized
[ 0.649832] highmem bounce pool size: 64 pages
[ 0.649837] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.649961] VFS: Disk quotas dquot_6.5.2
[ 0.650004] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.650066] msgmni has been set to 1724
[ 0.650242] alg: No test for stdrng (krng)
[ 0.650334] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 253)
[ 0.650338] io scheduler noop registered
[ 0.650340] io scheduler anticipatory registered
[ 0.650342] io scheduler deadline registered
[ 0.650372] io scheduler cfq registered (default)
[ 0.664100] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.664105] pci 0000:00:0b.0: Found disabled HT MSI Mapping
[ 0.664111] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.664117] pci 0000:00:0b.0: Linking AER extended capability
[ 0.664154] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.664158] pci 0000:00:0c.0: Found disabled HT MSI Mapping
[ 0.664165] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.664167] pci 0000:00:0c.0: Linking AER extended capability
[ 0.664208] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.664213] pci 0000:00:0d.0: Found disabled HT MSI Mapping
[ 0.664219] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.664222] pci 0000:00:0d.0: Linking AER extended capability
[ 0.664266] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.664270] pci 0000:00:0e.0: Found disabled HT MSI Mapping
[ 0.664277] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.664279] pci 0000:00:0e.0: Linking AER extended capability
[ 0.664293] pci 0000:01:09.0: Firmware left e100 interrupts enabled;
disabling
[ 0.664303] pci 0000:05:00.0: Boot video device
[ 0.664443] pcieport-driver 0000:00:0b.0: irq 24 for MSI/MSI-X
[ 0.664451] pcieport-driver 0000:00:0b.0: setting latency timer to 64
[ 0.664607] pcieport-driver 0000:00:0c.0: irq 25 for MSI/MSI-X
[ 0.664612] pcieport-driver 0000:00:0c.0: setting latency timer to 64
[ 0.664763] pcieport-driver 0000:00:0d.0: irq 26 for MSI/MSI-X
[ 0.664768] pcieport-driver 0000:00:0d.0: setting latency timer to 64
[ 0.664919] pcieport-driver 0000:00:0e.0: irq 27 for MSI/MSI-X
[ 0.664925] pcieport-driver 0000:00:0e.0: setting latency timer to 64
[ 0.665462] isapnp: Scanning for PnP cards...
[ 1.018088] isapnp: No Plug & Play device found
[ 1.021418] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.021537] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.021966] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.023842] brd: module loaded
[ 1.023949] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at
0x60,0x64 irq 1,12
[ 1.026462] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.026470] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.026674] mice: PS/2 mouse device common for all mice
[ 1.026760] rtc_cmos 00:04: RTC can wake from S4
[ 1.026838] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 1.026861] rtc0: alarms up to one year, y3k, 242 bytes nvram
[ 1.026895] cpuidle: using governor ladder
[ 1.026897] cpuidle: using governor menu
[ 1.026902] No iBFT detected.
[ 1.027304] TCP cubic registered
[ 1.027398] NET: Registered protocol family 10
[ 1.027901] lo: Disabled Privacy Extensions
[ 1.028209] Mobile IPv6
[ 1.028212] NET: Registered protocol family 17
[ 1.028223] Using IPI No-Shortcut mode
[ 1.028423] registered taskstats version 1
[ 1.028605] rtc_cmos 00:04: setting system clock to 2010-02-23
05:50:53 UTC (1266904253)
[ 1.028663] Freeing unused kernel memory: 320k freed
[ 1.029176] Write protecting the kernel text: 2176k
[ 1.029200] Write protecting the kernel read-only data: 772k
[ 1.057511] input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input0
[ 1.109482] fan PNP0C0B:00: registered as cooling_device0
[ 1.109491] ACPI: Fan [FAN] (on)
[ 1.112721] thermal LNXTHERM:01: registered as thermal_zone0
[ 1.112731] ACPI: Thermal Zone [THRM] (22 C)
[ 1.144229] Floppy drive(s): fd0 is 1.44M
[ 1.171349] SCSI subsystem initialized
[ 1.182902] FDC 0 is a post-1991 82077
[ 1.191972] Uniform Multi-Platform E-IDE driver
[ 1.201554] Linux agpgart interface v0.103
[ 1.204371] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[ 1.204376] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.204729] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
[ 1.204743] e100 0000:01:09.0: PCI INT A -> Link[APC4] -> GSI 19
(level, low) -> IRQ 19
[ 1.204814] e100 0000:01:09.0: setting latency timer to 64
[ 1.224430] e100 0000:01:09.0: PME# disabled
[ 1.225167] e100: eth0: e100_probe: addr 0xfdeff000, irq 19, MAC addr
00:d0:b7:85:0a:3f
[ 1.283668] nvidia: module license 'NVIDIA' taints kernel.
[ 1.283674] Disabling lock debugging due to kernel taint
[ 1.293914] usbcore: registered new interface driver usbfs
[ 1.293977] usbcore: registered new interface driver hub
[ 1.298924] usbcore: registered new device driver usb
[ 1.329266] libata version 3.00 loaded.
[ 1.332206] sata_nv 0000:00:07.0: version 3.5
[ 1.332639] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
[ 1.332652] sata_nv 0000:00:07.0: PCI INT A -> Link[APSI] -> GSI 23
(level, low) -> IRQ 23
[ 1.332722] sata_nv 0000:00:07.0: setting latency timer to 64
[ 1.336437] scsi0 : sata_nv
[ 1.336591] scsi1 : sata_nv
[ 1.336783] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xcc00
irq 23
[ 1.336786] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xcc08
irq 23
[ 1.336802] forcedeth: Reverse Engineered nForce ethernet driver.
Version 0.64.
[ 1.337134] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22
[ 1.337146] forcedeth 0000:00:0a.0: PCI INT A -> Link[APCH] -> GSI 22
(level, low) -> IRQ 22
[ 1.337151] forcedeth 0000:00:0a.0: setting latency timer to 64
[ 1.337218] nv_probe: set workaround bit for reversed mac addr
[ 1.389397] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.561311] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[ 1.561327] nvidia 0000:05:00.0: PCI INT A -> Link[APC3] -> GSI 18
(level, low) -> IRQ 18
[ 1.561338] nvidia 0000:05:00.0: setting latency timer to 64
[ 1.561666] NVRM: loading NVIDIA UNIX x86 Kernel Module 190.53 Tue
Dec 8 18:51:41 PST 2009
[ 1.856862] forcedeth 0000:00:0a.0: ifname eth1, PHY OUI 0x5043 @ 1,
addr 00:16:17:94:32:d6
[ 1.856867] forcedeth 0000:00:0a.0: highdma csum gbit lnktim desc-v3
[ 1.856903] amd74xx 0000:00:06.0: UDMA133 controller
[ 1.856907] amd74xx 0000:00:06.0: IDE controller (0x10de:0x0053 rev 0xf2)
[ 1.856939] amd74xx 0000:00:06.0: not 100% native mode: will probe
irqs later
[ 1.856945] ide0: BM-DMA at 0xe000-0xe007
[ 1.856953] ide1: BM-DMA at 0xe008-0xe00f
[ 1.856960] Probing IDE interface ide0...
[ 2.060026] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.145090] hda: ST380011A, ATA DISK drive
[ 2.480019] hdb: QUANTUM FIREBALLP LM15, ATA DISK drive
[ 2.480046] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 2.480295] hda: UDMA/100 mode selected
[ 2.480558] hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 2.480828] hdb: UDMA/66 mode selected
[ 2.481157] Probing IDE interface ide1...
[ 2.784021] ata2: SATA link down (SStatus 0 SControl 300)
[ 3.216097] hdc: TOSHIBA DVD-ROM SD-M1612, ATAPI CD/DVD-ROM drive
[ 4.057014] hdd: PLEXTOR CD-R PX-W1210A, ATAPI CD/DVD-ROM drive
[ 4.057054] hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 4.057487] hdc: UDMA/33 mode selected
[ 4.058065] hdd: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 4.058153] hdd: MWDMA2 mode selected
[ 4.058269] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 4.085016] ide1 at 0x170-0x177,0x376 on irq 15
[ 4.094528] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 21
[ 4.094540] sata_nv 0000:00:08.0: PCI INT A -> Link[APSJ] -> GSI 21
(level, low) -> IRQ 21
[ 4.094614] sata_nv 0000:00:08.0: setting latency timer to 64
[ 4.094807] scsi2 : sata_nv
[ 4.094911] scsi3 : sata_nv
[ 4.095056] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xb800
irq 21
[ 4.095059] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xb808
irq 21
[ 4.095357] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
[ 4.095363] ehci_hcd 0000:00:02.1: PCI INT B -> Link[APCL] -> GSI 20
(level, low) -> IRQ 20
[ 4.095373] ehci_hcd 0000:00:02.1: setting latency timer to 64
[ 4.095376] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 4.095424] ehci_hcd 0000:00:02.1: new USB bus registered, assigned
bus number 1
[ 4.095454] ehci_hcd 0000:00:02.1: debug port 1
[ 4.095458] ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
[ 4.095469] ehci_hcd 0000:00:02.1: irq 20, io mem 0xfeb00000
[ 4.105017] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
[ 4.105055] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.105058] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 4.105060] usb usb1: Product: EHCI Host Controller
[ 4.105062] usb usb1: Manufacturer: Linux 2.6.30-2-686 ehci_hcd
[ 4.105064] usb usb1: SerialNumber: 0000:00:02.1
[ 4.105134] usb usb1: configuration #1 chosen from 1 choice
[ 4.105162] hub 1-0:1.0: USB hub found
[ 4.105173] hub 1-0:1.0: 10 ports detected
[ 4.136952] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.137537] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
[ 4.137543] ohci_hcd 0000:00:02.0: PCI INT A -> Link[APCF] -> GSI 23
(level, low) -> IRQ 23
[ 4.137566] ohci_hcd 0000:00:02.0: setting latency timer to 64
[ 4.137569] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 4.137614] ohci_hcd 0000:00:02.0: new USB bus registered, assigned
bus number 2
[ 4.137636] ohci_hcd 0000:00:02.0: irq 23, io mem 0xfe02f000
[ 4.194028] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.194031] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 4.194034] usb usb2: Product: OHCI Host Controller
[ 4.194036] usb usb2: Manufacturer: Linux 2.6.30-2-686 ohci_hcd
[ 4.194038] usb usb2: SerialNumber: 0000:00:02.0
[ 4.194100] usb usb2: configuration #1 chosen from 1 choice
[ 4.194129] hub 2-0:1.0: USB hub found
[ 4.194139] hub 2-0:1.0: 10 ports detected
[ 4.664017] usb 2-7: new low speed USB device using ohci_hcd and
address 2
[ 4.820021] ata3: SATA link down (SStatus 0 SControl 300)
[ 5.036042] usb 2-7: New USB device found, idVendor=051d, idProduct=0002
[ 5.036046] usb 2-7: New USB device strings: Mfr=3, Product=1,
SerialNumber=2
[ 5.036049] usb 2-7: Product: Back-UPS RS 1500 FW:8.g8 .D USB FW:g8
[ 5.036051] usb 2-7: Manufacturer: American Power Conversion
[ 5.036053] usb 2-7: SerialNumber: QB0512132444
[ 5.036127] usb 2-7: configuration #1 chosen from 1 choice
[ 5.544022] ata4: SATA link down (SStatus 0 SControl 300)
[ 5.552444] ide-gd driver 1.18
[ 5.552494] hda: max request size: 512KiB
[ 5.554615] hda: 156301488 sectors (80026 MB) w/2048KiB Cache,
CHS=16383/255/63
[ 5.554828] hda: cache flushes supported
[ 5.554897] hda:<6>ide-cd driver 5.00
[ 5.561209] hda1 hda2 <<6>usbcore: registered new interface driver
hiddev
[ 5.571415] hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 >
[ 5.639256] hdb: max request size: 128KiB
[ 5.639517] hdb: 29336832 sectors (15020 MB) w/1900KiB Cache,
CHS=29104/16/63
[ 5.639521] hdb: cache flushes not supported
[ 5.639555] hdb: hdb1
[ 5.649022] ide-cd: hdc: ATAPI 48X DVD-ROM drive, 512kB Cache
[ 5.649027] Uniform CD-ROM driver Revision: 3.20
[ 5.663083] ide-cd: hdd: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache
[ 6.640149] generic-usb 0003:051D:0002.0001: hiddev96,hidraw0: USB
HID v1.10 Device [American Power Conversion Back-UPS RS 1500 FW:8.g8 .D
USB FW:g8 ] on usb-0000:00:02.0-7/input0
[ 6.640173] usbcore: registered new interface driver usbhid
[ 6.640176] usbhid: v2.6:USB HID core driver
[ 6.696783] PM: Starting manual resume from disk
[ 6.744838] kjournald starting. Commit interval 5 seconds
[ 6.744865] EXT3-fs: mounted filesystem with ordered data mode.
[ 8.782937] udev: starting version 151
[ 9.012374] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 9.012383] ACPI: Power Button [PWRF]
[ 9.012461] input: Power Button as
/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
[ 9.012464] ACPI: Power Button [PWRB]
[ 9.017367] processor ACPI_CPU:00: registered as cooling_device1
[ 9.017408] processor ACPI_CPU:01: registered as cooling_device2
[ 9.288872] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 9.470625] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x4c00
[ 9.470645] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x4c40
[ 9.478733] udev: renamed network interface eth1 to eth0
[ 9.528792] udev: renamed network interface eth0_rename to eth1
[ 9.763461] input: ImPS/2 Generic Wheel Mouse as
/devices/platform/i8042/serio1/input/input4
[ 10.441297] ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
[ 10.441305] Intel ICH 0000:00:04.0: PCI INT A -> Link[APCJ] -> GSI 22
(level, low) -> IRQ 22
[ 10.441355] Intel ICH 0000:00:04.0: setting latency timer to 64
[ 10.764025] intel8x0_measure_ac97_clock: measured 53598 usecs (2632
samples)
[ 10.764029] intel8x0: clocking to 46918
[ 11.098783] Adding 2361512k swap on /dev/hda10. Priority:-1
extents:1 across:2361512k
[ 11.261075] EXT3 FS on hda1, internal journal
[ 11.480753] loop: module loaded
[ 11.520487] w83627ehf: Found W83627EHG chip at 0x290
[ 11.608265] fuse init (API version 7.11)
[ 11.676576] device-mapper: uevent: version 1.0.3
[ 11.676856] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23)
initialised: dm-***@redhat.com
[ 13.751947] kjournald starting. Commit interval 5 seconds
[ 13.752131] EXT3 FS on hda5, internal journal
[ 13.752140] EXT3-fs: mounted filesystem with ordered data mode.
[ 13.772284] kjournald starting. Commit interval 5 seconds
[ 13.772447] EXT3 FS on hda6, internal journal
[ 13.772450] EXT3-fs: mounted filesystem with ordered data mode.
[ 13.795211] kjournald starting. Commit interval 5 seconds
[ 13.795385] EXT3 FS on hda7, internal journal
[ 13.795388] EXT3-fs: mounted filesystem with ordered data mode.
[ 13.910813] kjournald starting. Commit interval 5 seconds
[ 13.911026] EXT3 FS on hda8, internal journal
[ 13.911035] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.117236] kjournald starting. Commit interval 5 seconds
[ 14.117464] EXT3 FS on hda9, internal journal
[ 14.117473] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.317076] kjournald starting. Commit interval 5 seconds
[ 14.463960] EXT3 FS on hda11, internal journal
[ 14.463970] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.483453] kjournald starting. Commit interval 5 seconds
[ 14.483627] EXT3 FS on hda12, internal journal
[ 14.483635] EXT3-fs: mounted filesystem with ordered data mode.
[ 14.494846] kjournald starting. Commit interval 5 seconds
[ 14.495199] EXT3 FS on hdb1, internal journal
[ 14.495202] EXT3-fs: mounted filesystem with ordered data mode.
[ 15.861859] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 15.925097] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 15.925329] CONFIG_NF_CT_ACCT is deprecated and will be removed soon.
Please use
[ 15.925331] nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack
module option or
[ 15.925333] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 19.357730] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core
Processor 4600+ processors (2 cpu cores) (version 2.20.00)
[ 19.357763] [Firmware Bug]: powernow-k8: No compatible ACPI _PSS
objects found.
[ 19.357766] [Firmware Bug]: powernow-k8: Try again with latest BIOS.
[ 27.180025] eth0: no IPv6 routers present
[ 31.449879] hdd: task_pio_intr: status=0x51 { DriveReady SeekComplete
Error }
[ 31.450064] hdd: task_pio_intr: error=0x04 { AbortedCommand }
[ 31.450200] hdd: possibly failed opcode: 0xec
[ 33.312510] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 33.312514] vboxdrv: Successfully done.
[ 33.312517] vboxdrv: Found 2 processor cores.
[ 33.312597] vboxdrv: fAsync=1 offMin=0x197a4f offMax=0x197a4f
[ 33.312652] vboxdrv: TSC mode is 'asynchronous', kernel timer mode is
'normal'.
[ 33.312654] vboxdrv: Successfully loaded version 3.1.2 (interface
0x00100001).
[ 35.635004] Bluetooth: Core ver 2.15
[ 35.635134] NET: Registered protocol family 31
[ 35.635136] Bluetooth: HCI device and connection manager initialized
[ 35.635141] Bluetooth: HCI socket layer initialized
[ 35.668304] Bluetooth: L2CAP ver 2.13
[ 35.668308] Bluetooth: L2CAP socket layer initialized
[ 35.860613] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 35.860618] Bluetooth: BNEP filters: protocol multicast
[ 35.924776] Bridge firewalling registered
[ 35.961215] Bluetooth: RFCOMM socket layer initialized
[ 35.961230] Bluetooth: RFCOMM TTY layer initialized
[ 35.961232] Bluetooth: RFCOMM ver 1.11
[ 36.079719] Bluetooth: SCO (Voice Link) ver 0.6
[ 36.079723] Bluetooth: SCO socket layer initialized
[ 37.045568] e100 0000:01:09.0: firmware: requesting e100/d101m_ucode.bin
[ 37.116299] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 37.641890] lp: driver loaded but no devices found
[ 37.647358] ppdev: user-space parallel port driver

How can I remove/disable it since this old box and I don't have and use
Bluetooth. I tried looking through my installed Debian packages and only
found:

$ dpkg -l | grep ^ii |grep bluetooth
ii gnome-bluetooth 2.28.6-2
GNOME Bluetooth tools
ii libbluetooth3 4.60-1
Library to use the BlueZ Linux Bluetooth stack
ii libgnome-bluetooth7 2.28.6-2
GNOME Bluetooth tools - support library

I tried removing each one, but they seem to remove Gnome which I do not
want to do. I am not even sure if that is where Bluetooth is coming from
and I wasn't even in Gnome/X.

I assume it is from Kernel because of:
$ lsmod |grep bluetooth
bluetooth 46960 6 sco,rfcomm,bnep,l2cap

AND

$ locate bluetooth
/etc/bluetooth
/etc/bluetooth/audio.conf
/etc/bluetooth/input.conf
/etc/bluetooth/main.conf
/etc/bluetooth/network.conf
/etc/bluetooth/rfcomm.conf
/etc/dbus-1/system.d/bluetooth.conf
/etc/default/bluetooth
/etc/init.d/bluetooth
/etc/rc0.d/K74bluetooth
/etc/rc1.d/K74bluetooth
/etc/rc2.d/S25bluetooth
/etc/rc3.d/S25bluetooth
/etc/rc4.d/S25bluetooth
/etc/rc5.d/S25bluetooth
/etc/rc6.d/K74bluetooth
/etc/xdg/autostart/bluetooth-applet.desktop
/lib/modules/2.6.30-2-686/kernel/drivers/bluetooth
/lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/bcm203x.ko
/lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/bfusb.ko
/lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/bluecard_cs.ko
/lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/bpa10x.ko
/lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/bt3c_cs.ko
/lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/btsdio.ko
/lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/btuart_cs.ko
/lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/btusb.ko
/lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/dtl1_cs.ko
/lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/hci_uart.ko
/lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/hci_vhci.ko
/lib/modules/2.6.30-2-686/kernel/net/bluetooth
/lib/modules/2.6.30-2-686/kernel/net/bluetooth/bluetooth.ko
/lib/modules/2.6.30-2-686/kernel/net/bluetooth/bnep
/lib/modules/2.6.30-2-686/kernel/net/bluetooth/cmtp
/lib/modules/2.6.30-2-686/kernel/net/bluetooth/hidp
/lib/modules/2.6.30-2-686/kernel/net/bluetooth/l2cap.ko
/lib/modules/2.6.30-2-686/kernel/net/bluetooth/rfcomm
/lib/modules/2.6.30-2-686/kernel/net/bluetooth/sco.ko
/lib/modules/2.6.30-2-686/kernel/net/bluetooth/bnep/bnep.ko
/lib/modules/2.6.30-2-686/kernel/net/bluetooth/cmtp/cmtp.ko
/lib/modules/2.6.30-2-686/kernel/net/bluetooth/hidp/hidp.ko
/lib/modules/2.6.30-2-686/kernel/net/bluetooth/rfcomm/rfcomm.ko
/lib/udev/rules.d/61-gnome-bluetooth-rfkill.rules
/usr/bin/bluetooth-agent
/usr/bin/bluetooth-applet
/usr/bin/bluetooth-properties
/usr/bin/bluetooth-sendto
/usr/bin/bluetooth-wizard
/usr/lib/bluetooth
/usr/lib/gnome-bluetooth
/usr/lib/libbluetooth.so.2
/usr/lib/libbluetooth.so.2.8.1
/usr/lib/libbluetooth.so.3
/usr/lib/libbluetooth.so.3.5.0
/usr/lib/libgnome-bluetooth.so.7
/usr/lib/libgnome-bluetooth.so.7.0.2
/usr/lib/bluetooth/plugins
/usr/lib/bluetooth/plugins/netlink.so
/usr/lib/gnome-bluetooth/plugins
/usr/lib/gnome-bluetooth/plugins/libgbtgeoclue.so
/usr/lib/gnome-bluetooth/plugins/libnma.so
/usr/lib/hal/hald-probe-net-bluetooth
/usr/sbin/bluetoothd
/usr/share/gnome-bluetooth
/usr/share/app-install/desktop/bluetooth-properties.desktop
/usr/share/app-install/desktop/gpe-bluetooth.desktop
/usr/share/app-install/desktop/kbluetooth.desktop
/usr/share/app-install/icons/bluetooth.png
/usr/share/app-install/icons/kdebluetooth.png
/usr/share/applications/bluetooth-properties.desktop
/usr/share/doc/gnome-bluetooth
/usr/share/doc/libbluetooth3
/usr/share/doc/libgnome-bluetooth7
/usr/share/doc/bluez/examples/monitor-bluetooth
/usr/share/doc/gnome-bluetooth/AUTHORS
/usr/share/doc/gnome-bluetooth/NEWS.gz
/usr/share/doc/gnome-bluetooth/README
/usr/share/doc/gnome-bluetooth/changelog.Debian.gz
/usr/share/doc/gnome-bluetooth/changelog.gz
/usr/share/doc/gnome-bluetooth/copyright
/usr/share/doc/libbluetooth3/AUTHORS
/usr/share/doc/libbluetooth3/NEWS.Debian.gz
/usr/share/doc/libbluetooth3/README
/usr/share/doc/libbluetooth3/README.Debian.gz
/usr/share/doc/libbluetooth3/changelog.Debian.gz
/usr/share/doc/libbluetooth3/changelog.gz
/usr/share/doc/libbluetooth3/copyright
/usr/share/doc/libgnome-bluetooth7/AUTHORS
/usr/share/doc/libgnome-bluetooth7/NEWS.gz
/usr/share/doc/libgnome-bluetooth7/README
/usr/share/doc/libgnome-bluetooth7/changelog.Debian.gz
/usr/share/doc/libgnome-bluetooth7/changelog.gz
/usr/share/doc/libgnome-bluetooth7/copyright
/usr/share/gconf/schemas/bluetooth-manager.schemas
/usr/share/gnome/autostart/bluetooth-applet.desktop
/usr/share/gnome/help/gnome-bluetooth
/usr/share/gnome/help/gnome-bluetooth/C
/usr/share/gnome/help/gnome-bluetooth/C/figures
/usr/share/gnome/help/gnome-bluetooth/C/gnome-bluetooth.xml
/usr/share/gnome/help/gnome-bluetooth/C/legal.xml
/usr/share/gnome/help/gnome-bluetooth/C/figures/bluetooth-applet.png
/usr/share/gnome/help/gnome-bluetooth/C/figures/bluetooth-properties.png
/usr/share/gnome/help/gnome-bluetooth/C/figures/bluetooth-wizard.png
/usr/share/gnome/help/gnome-user-share/C/figures/receiving-over-bluetooth.png
/usr/share/gnome/help/gnome-user-share/C/figures/sharing-over-bluetooth.png
/usr/share/gnome-bluetooth/authorisation-dialogue.ui
/usr/share/gnome-bluetooth/confirm-dialogue.ui
/usr/share/gnome-bluetooth/passkey-dialogue.ui
/usr/share/gnome-bluetooth/pin-code-database.xml
/usr/share/gnome-bluetooth/popup-menu.ui
/usr/share/gnome-bluetooth/properties-adapter-off.ui
/usr/share/gnome-bluetooth/properties-no-adapter.ui
/usr/share/gnome-bluetooth/wizard.ui
/usr/share/hal/fdi/information/10freedesktop/10-dell-rfkill-switch-bluetooth.fdi
/usr/share/hal/fdi/information/10freedesktop/10-sony-bluetooth-switch.fdi
/usr/share/hal/fdi/information/10freedesktop/10-thinkpad-rfkill-switch-bluetooth.fdi
/usr/share/icons/hicolor/16x16/apps/bluetooth.png
/usr/share/icons/hicolor/16x16/status/bluetooth-disabled.png
/usr/share/icons/hicolor/16x16/status/bluetooth-paired.png
/usr/share/icons/hicolor/22x22/apps/bluetooth.png
/usr/share/icons/hicolor/22x22/status/bluetooth-disabled.png
/usr/share/icons/hicolor/22x22/status/bluetooth-paired.png
/usr/share/icons/hicolor/24x24/apps/bluetooth.png
/usr/share/icons/hicolor/24x24/status/bluetooth-disabled.png
/usr/share/icons/hicolor/24x24/status/bluetooth-paired.png
/usr/share/icons/hicolor/32x32/apps/bluetooth.png
/usr/share/icons/hicolor/32x32/status/bluetooth-disabled.png
/usr/share/icons/hicolor/32x32/status/bluetooth-paired.png
/usr/share/icons/hicolor/48x48/apps/bluetooth.png
/usr/share/icons/hicolor/48x48/status/bluetooth-disabled.png
/usr/share/icons/hicolor/scalable/apps/bluetooth.svg
/usr/share/icons/hicolor/scalable/status/bluetooth-paired.svg
/usr/share/man/man1/bluetooth-applet.1.gz
/usr/share/man/man1/bluetooth-properties.1.gz
/usr/share/man/man1/bluetooth-sendto.1.gz
/usr/share/man/man1/bluetooth-wizard.1.gz
/usr/share/man/man8/bluetoothd.8.gz
/usr/share/omf/gnome-bluetooth
/usr/share/omf/gnome-bluetooth/gnome-bluetooth-C.omf
/usr/src/linux-headers-2.6.30-2-common/include/net/bluetooth
/usr/src/linux-headers-2.6.30-2-common/include/net/bluetooth/bluetooth.h
/usr/src/linux-headers-2.6.30-2-common/include/net/bluetooth/hci.h
/usr/src/linux-headers-2.6.30-2-common/include/net/bluetooth/hci_core.h
/usr/src/linux-headers-2.6.30-2-common/include/net/bluetooth/l2cap.h
/usr/src/linux-headers-2.6.30-2-common/include/net/bluetooth/rfcomm.h
/usr/src/linux-headers-2.6.30-2-common/include/net/bluetooth/sco.h
/var/lib/dpkg/info/gnome-bluetooth.list
/var/lib/dpkg/info/gnome-bluetooth.md5sums
/var/lib/dpkg/info/gnome-bluetooth.postinst
/var/lib/dpkg/info/gnome-bluetooth.prerm
/var/lib/dpkg/info/libbluetooth2.list
/var/lib/dpkg/info/libbluetooth2.postrm
/var/lib/dpkg/info/libbluetooth3.list
/var/lib/dpkg/info/libbluetooth3.md5sums
/var/lib/dpkg/info/libbluetooth3.postinst
/var/lib/dpkg/info/libbluetooth3.postrm
/var/lib/dpkg/info/libbluetooth3.shlibs
/var/lib/dpkg/info/libbluetooth3.symbols
/var/lib/dpkg/info/libgnome-bluetooth2.list
/var/lib/dpkg/info/libgnome-bluetooth2.postrm
/var/lib/dpkg/info/libgnome-bluetooth7.list
/var/lib/dpkg/info/libgnome-bluetooth7.md5sums
/var/lib/dpkg/info/libgnome-bluetooth7.postinst
/var/lib/dpkg/info/libgnome-bluetooth7.postrm
/var/lib/dpkg/info/libgnome-bluetooth7.shlibs
/var/lib/dpkg/info/libgnome-bluetooth7.symbols
/var/lib/update-rc.d/bluetooth

Do I assume I have to customize Kernel to remove it?

FYI, my system specifications/configurations: AMD Athlon 64 X2 (dual
core) 939 4600+ CPU (using a Thermaltake Silent Boost K8 A1838 model),
MSI K8N NEO4-F (MS-7125) motherboard (NVIDIA nForce4), 2.5 GB of RAM
(one 1 GB + three 512 MB; use all four memory slots) refurbished (RMA'ed
twice!) EVGA GeForce 8800 GT (PCIE; NVIDIA), Enlight 7237-ATX mid-tower
case; Antec Basiq 500 Watt ATX Power Supply (BP500U), two case 80mm case
fans, Seagate Barracuda 7200.7 (ST380011A; 7200 RPM; 80 GB) HDD, an IDE
Quantum Fireball Plus LM 15 GB, Toshiba DVD-ROM SD-M1612 Rev. B 16X/48X
ATAPI/IDE drive, Plextor PX-W1210 PlexWriter (12/10/32A; IDE), 3.5"
floppy disk drive, and an Intel InBusiness 10/100 (82559) NIC. Running
Debian (Linux) OS (Kernel v2.6.30-...-686).

Thank you in advance. :)
--
"Really. And do these lions eat ants?" --John Cleese in Monty Python's
Flying Circus
/\___/\
/ /\ /\ \ Phil./Ant @ http://antfarm.ma.cx (Personal Web Site)
| |o o| | Ant's Quality Foraged Links: http://aqfl.net
\ _ / Nuke ANT from e-mail address: ***@earthlink.netANT
( ) or ***@zimage.com
Ant is currently not listening to any songs on his home computer.
Lusotec
2010-02-23 15:53:14 UTC
Permalink
Ant wrote:
> Do I assume I have to customize Kernel to remove it (bluetooth)?

No, you only need to disable the bluetooth driver module.

To disable a module, in this case bluetooth, you need to do the following:

1) Create a new file in the directory /etc/modprobe.d/. In this case
I recommend a pathname like /etc/modprobe.d/blacklist-bluetooth

2) Edit the above file and put in it the following line:

blacklist bluetooth

3) Reboot the system (a reboot is not exactly needed but it the simplest way
to activate the new configuration)


After this change your system will *not* load the bluetooth module and thus
bluetooth support will be disabled.

The above steps can be done for any module, just change 'bluetooth' to the
name of the module you want to disable.

Regards.
David Kerber
2010-02-23 15:55:50 UTC
Permalink
In article <***@earthlink.com>,
***@zimage.comANT says...
>
> Hello.
>
> I noticed my old Debian box, with Kernel v2.6.30-2-686 #1 SMP Fri Dec 4
> 00:53:20 UTC 2009 i686 GNU/Linux, has Bluetooth installed and running.
> Is that part of the kernel or somewhere else? Dmesg command showed:

I was able to just uninstall the bluetooth stuff with the package
manager. I haven't a clue as to why it was installed by default, since
there is no bluetooth hdwe in that box.

D
Ant
2010-02-23 16:08:50 UTC
Permalink
On 2/23/2010 7:55 AM PT, David Kerber typed:

> I was able to just uninstall the bluetooth stuff with the package
> manager. I haven't a clue as to why it was installed by default, since
> there is no bluetooth hdwe in that box.

Which package manager? I tried both apt-get and aptitude. :(
--
"Ants are so much like human beings as to be an embarrassment. They farm
fungi, raise aphids as livestock, launch armies into wars, use chemical
sprays to alarm and confuse enemies, capture slaves. The families of
weaver ants engage in child labor, holding their larvae like shuttles to
spin out the thread that sews the leaves together for their fungus
gardens. They exchange information ceaselessly. They do everything but
watch television." --Lewis Thomas
/\___/\
/ /\ /\ \ Phil./Ant @ http://antfarm.ma.cx (Personal Web Site)
| |o o| | Ant's Quality Foraged Links: http://aqfl.net
\ _ / Nuke ANT from e-mail address: ***@earthlink.netANT
( ) or ***@zimage.com
Ant is currently not listening to any songs on his home computer.
David Kerber
2010-02-23 17:33:30 UTC
Permalink
In article <***@earthlink.com>,
***@zimage.comANT says...
>
> On 2/23/2010 7:55 AM PT, David Kerber typed:
>
> > I was able to just uninstall the bluetooth stuff with the package
> > manager. I haven't a clue as to why it was installed by default, since
> > there is no bluetooth hdwe in that box.
>
> Which package manager? I tried both apt-get and aptitude. :(

Synaptic; I didn't try apt-get, and have never used aptitude.

D
Ant
2010-02-24 02:17:53 UTC
Permalink
On 2/23/2010 9:33 AM PT, David Kerber typed:

> In article<***@earthlink.com>,
> ***@zimage.comANT says...
>>
>> On 2/23/2010 7:55 AM PT, David Kerber typed:
>>
>>> I was able to just uninstall the bluetooth stuff with the package
>>> manager. I haven't a clue as to why it was installed by default, since
>>> there is no bluetooth hdwe in that box.
>>
>> Which package manager? I tried both apt-get and aptitude. :(
>
> Synaptic; I didn't try apt-get, and have never used aptitude.

Ah, I am a command console user for updating.
--
..."Like me with the anthill in my backyard. I spent days watching the
ants, trying to figure out which ones were good, and which ones were
bad, but they all just looked like ants, so I started smiting all of
them." "Well that's not --" "I was smiting them with the garden hose,
and with lighter fluid, and with the lawnmower, and to be perfectly
honest, I think I went a little crazy with the shovel. Those ants could
have been praying to me all day, I wouldn't have heard them." "There was
nothing they could do about it." "But, I don't think --" "Really, it's
the same with us. There's nothing we can do about anything either, so
why worry about it? Hey, this is making me feel better." "Well, that's
good, but --" "I guess all we can do is live our lives with as much
kindness and decency as possible, and try not to dwell on God standing
over us with a giant shovel."...--Dewey and Teacher in Day Care episode
from Malcolm in the Middle
/\___/\
/ /\ /\ \ Phil./Ant @ http://antfarm.ma.cx (Personal Web Site)
| |o o| | Ant's Quality Foraged Links: http://aqfl.net
\ _ / Nuke ANT from e-mail address: ***@earthlink.netANT
( ) or ***@zimage.com
Ant is currently not listening to any songs on his home computer.
Kevin D. Snodgrass
2010-02-23 20:44:23 UTC
Permalink
> I assume it is from Kernel because of:
> $ lsmod |grep bluetooth
> bluetooth 46960 6 sco,rfcomm,bnep,l2cap

This means it is a kernel module.

> $ locate bluetooth
> /etc/bluetooth
> /etc/bluetooth/audio.conf
> /etc/bluetooth/input.conf
> /etc/bluetooth/main.conf
> /etc/bluetooth/network.conf
> /etc/bluetooth/rfcomm.conf
> /etc/dbus-1/system.d/bluetooth.conf
> /etc/default/bluetooth
> /etc/init.d/bluetooth
> /etc/rc0.d/K74bluetooth
> /etc/rc1.d/K74bluetooth
> /etc/rc2.d/S25bluetooth
> /etc/rc3.d/S25bluetooth
> /etc/rc4.d/S25bluetooth
> /etc/rc5.d/S25bluetooth
> /etc/rc6.d/K74bluetooth

Delete or rename (move somewhere else, outside the /etc/init.d/ and
/etc/rc?.d/ directories) the bluetooth scripts in the various rc?.d
directories. That should keep the various bluetooth modules from
getting loaded.

> /etc/xdg/autostart/bluetooth-applet.desktop
> /lib/modules/2.6.30-2-686/kernel/drivers/bluetooth
> /lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/bcm203x.ko
> /lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/bfusb.ko
> /lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/bluecard_cs.ko
> /lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/bpa10x.ko
> /lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/bt3c_cs.ko
> /lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/btsdio.ko
> /lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/btuart_cs.ko
> /lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/btusb.ko
> /lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/dtl1_cs.ko
> /lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/hci_uart.ko
> /lib/modules/2.6.30-2-686/kernel/drivers/bluetooth/hci_vhci.ko
> /lib/modules/2.6.30-2-686/kernel/net/bluetooth
> /lib/modules/2.6.30-2-686/kernel/net/bluetooth/bluetooth.ko
> /lib/modules/2.6.30-2-686/kernel/net/bluetooth/bnep
> /lib/modules/2.6.30-2-686/kernel/net/bluetooth/cmtp
> /lib/modules/2.6.30-2-686/kernel/net/bluetooth/hidp
> /lib/modules/2.6.30-2-686/kernel/net/bluetooth/l2cap.ko
> /lib/modules/2.6.30-2-686/kernel/net/bluetooth/rfcomm
> /lib/modules/2.6.30-2-686/kernel/net/bluetooth/sco.ko
> /lib/modules/2.6.30-2-686/kernel/net/bluetooth/bnep/bnep.ko
> /lib/modules/2.6.30-2-686/kernel/net/bluetooth/cmtp/cmtp.ko
> /lib/modules/2.6.30-2-686/kernel/net/bluetooth/hidp/hidp.ko
> /lib/modules/2.6.30-2-686/kernel/net/bluetooth/rfcomm/rfcomm.ko

There are the kernel modules (*.ko).

> Do I assume I have to customize Kernel to remove it?

No, just prevent the kernel modules from loading. Either my way,
delete/rename the scripts in /etc/rc?.d (actually symlinks, but...) or
do what another poster suggested and blacklist. I prefer to
delete/rename since the bootup won't even spend time reading in the
scripts and checking the blacklist.

> Thank you in advance. :)

Hey Phil, you still reading comp.os.netware.*? :-)
Ant
2010-02-24 02:19:18 UTC
Permalink
On 2/23/2010 12:44 PM PT, Kevin D. Snodgrass typed:

> Hey Phil, you still reading comp.os.netware.*? :-)

Thanks for the tips. I never read comp.os.netware.* nor used Netware
before. Maybe confused with another Phil.?
--
"Be thine enemy an ant, see in him an elephant." --Turkish Proverb
/\___/\
/ /\ /\ \ Phil./Ant @ http://antfarm.ma.cx (Personal Web Site)
| |o o| | Ant's Quality Foraged Links: http://aqfl.net
\ _ / Nuke ANT from e-mail address: ***@earthlink.netANT
( ) or ***@zimage.com
Ant is currently not listening to any songs on his home computer.
Matt Giwer
2010-02-26 07:10:15 UTC
Permalink
On 02/23/2010 09:29 AM, Ant wrote:
> Hello.
>
> I noticed my old Debian box, with Kernel v2.6.30-2-686 #1 SMP Fri Dec 4
> 00:53:20 UTC 2009 i686 GNU/Linux, has Bluetooth installed and running.
> Is that part of the kernel or somewhere else? Dmesg command showed:
...
> /var/lib/update-rc.d/bluetooth
>
> Do I assume I have to customize Kernel to remove it?

Try simply chkconfig for bluetooth and then as root turn it off.

--
The standard of justice for Palestinians is the same standard Jews demand
for themselves from Germany.
-- The Iron Webmaster, 4229
http://www.giwersworld.org/holo2/ a11
Fri Feb 26 02:08:21 EST 2010
Ant
2010-02-26 08:57:09 UTC
Permalink
On 2/25/2010 11:10 PM PT, Matt Giwer typed:

> Try simply chkconfig for bluetooth and then as root turn it off.

Neat command after installing chkconfig package. I saw a lot of stuff
that were on:

# chkconfig
acpid on
alsa-utils on
and on
apache2 on
apcupsd 12345
arpwatch on
atd on
avahi-daemon on
binfmt-support on
bluetooth on
bootlogd on
bootlogs on
bootmisc.sh on
checkfs.sh on
checkroot.sh on
clamav-freshclam on
console-screen.sh on
console-setup on
cpufreqd on
cpufrequtils on
cron on
cups on
dbus on
denyhosts on
dirmngr on
exim4 on
fuse on
gdm on
gpm on
guarddog on
hal on
hddtemp on
hdparm on
hostname.sh on
hwclock.sh on
hwclock.sh.dpkg-old off
hwclockfirst.sh on
hwclockfirst.sh.dpkg-old off
ifupdown 0S
ifupdown-clean on
keyboard-setup on
keymap.sh on
killprocs on
klogd on
libdevmapper1.02 S
lm-sensors on
loadcpufreq on
module-init-tools on
mountall-bootclean.sh on
mountall.sh on
mountdevsubfs.sh on
mountkernfs.sh on
mountnfs-bootclean.sh on
mountnfs.sh on
mountoverflowtmp on
mtab.sh on
netdiag on
network-manager on
networking 0S
nfs-common on
ntop 2345
ntp on
openbsd-inetd on
pcscd on
policykit on
portmap 02345S
powernowd on
pppd-dns on
preload on
procps on
rc.local on
rcS off
rmnologin on
rsync on
samba on
screen-cleanup on
sendsigs 0
smartmontools on
ssh on
stop-bootlogd on
stop-bootlogd-single on
stunnel4 on
sudo on
sudo.dpkg-bak off
sysklogd on
sysstat on
udev on
udev-mtab on
umountfs 0
umountnfs.sh 0
umountroot 0
ups-monitor off
urandom 0S
vboxdrv on
vboxnet on
vsftpd on
wifi-radar 2345
wpa-ifupdown 0
x11-common on
yum-updatesd on
zope2.10 on
zope2.9 on
zope3 on

I will have to mess with them since there seems to be a lot of services
to disable that I don't need.
--
"... Our latest evil plan and create an army of giant ants to take over
the galaxy..." --Dark Helmet from Spaceballs: The Animated Series (S1 E3).
/\___/\
/ /\ /\ \ Phil./Ant @ http://antfarm.ma.cx (Personal Web Site)
| |o o| | Ant's Quality Foraged Links: http://aqfl.net
\ _ / Nuke ANT from e-mail address: ***@earthlink.netANT
( ) or ***@zimage.com
Ant is currently not listening to any songs on his home computer.
Tecknode
2010-03-01 20:28:25 UTC
Permalink
Matt Giwer wrote:
> On 02/23/2010 09:29 AM, Ant wrote:
>> Hello.
>>
>> I noticed my old Debian box, with Kernel v2.6.30-2-686 #1 SMP Fri Dec 4
>> 00:53:20 UTC 2009 i686 GNU/Linux, has Bluetooth installed and running.
>> Is that part of the kernel or somewhere else? Dmesg command showed:
> ...
>> /var/lib/update-rc.d/bluetooth
>>
>> Do I assume I have to customize Kernel to remove it?
>
> Try simply chkconfig for bluetooth and then as root turn it off.
>

If Bluetooth is installed, it is because you have Bluetooth card in
your hardware. That is why Debian installed the driver.
David Kerber
2010-03-01 22:13:58 UTC
Permalink
In article <KrVin.260703$***@en-nntp-03.dc1.easynews.com>,
***@NOSPAM.com says...
>
> Matt Giwer wrote:
> > On 02/23/2010 09:29 AM, Ant wrote:
> >> Hello.
> >>
> >> I noticed my old Debian box, with Kernel v2.6.30-2-686 #1 SMP Fri Dec 4
> >> 00:53:20 UTC 2009 i686 GNU/Linux, has Bluetooth installed and running.
> >> Is that part of the kernel or somewhere else? Dmesg command showed:
> > ...
> >> /var/lib/update-rc.d/bluetooth
> >>
> >> Do I assume I have to customize Kernel to remove it?
> >
> > Try simply chkconfig for bluetooth and then as root turn it off.
> >
>
> If Bluetooth is installed, it is because you have Bluetooth card in
> your hardware. That is why Debian installed the driver.

Nope. I've put debian Lenny on 3 different machines, none of which had
any bluetooth hardware on it, and one of which predated the advent of
bluetooth, and got the bluetooth installed on all 3 of them when using a
default install.

D
Harold Stevens
2010-03-01 22:59:32 UTC
Permalink
In <***@news.conversent.net> David Kerber:

[Snip...]

> got the bluetooth installed on all 3 of them when using a default install

AFAICT, this is also my experience, but includes distros other than only
the Debian-based. Bluetooth seems there, whether BT hardware or not.

JMO; YMMV...

--
Regards, Weird (Harold Stevens) * IMPORTANT EMAIL INFO FOLLOWS *
Pardon any bogus email addresses (wookie) in place for spambots.
Really, it's (wyrd) at airmail, dotted with net. DO NOT SPAM IT.
I toss GoogleGroup (http://twovoyagers.com/improve-usenet.org/).
Matt Giwer
2010-03-02 05:49:17 UTC
Permalink
On 03/01/2010 03:28 PM, Tecknode wrote:
> Matt Giwer wrote:
>> On 02/23/2010 09:29 AM, Ant wrote:
>>> Hello.
>>> I noticed my old Debian box, with Kernel v2.6.30-2-686 #1 SMP Fri Dec 4
>>> 00:53:20 UTC 2009 i686 GNU/Linux, has Bluetooth installed and running.
>>> Is that part of the kernel or somewhere else? Dmesg command showed:
>> ...
>>> /var/lib/update-rc.d/bluetooth
>>> Do I assume I have to customize Kernel to remove it?
>> Try simply chkconfig for bluetooth and then as root turn it off.

> If Bluetooth is installed, it is because you have Bluetooth card in your
> hardware. That is why Debian installed the driver.

My quad has bluetooth and RJ-45. Fedora 12 installed both drivers. I do not
not use bluetooth so I turned it off. It harms nothing and has a slight
theoretical gain in boot time and swap space used. I can't say I noticed a
difference. I doubt he has noticed an improvement but maybe so. I answered the
question asked.

Lots of things are always on that are not necessarily used. Look for mysqld
for example. These services are turned on for whatever your dozens of users
might have in mind. These distros do not have home users in mind.

And all of this brings up a gripe I am still formulating about the assumption
of many users in these distros. I don't really complain because I enjoy this
stuff. I just came across practice certification test and I can almost pass.
(Lots of people have said I am certifiable but I think they were talking about
something else.) After ten years of curious maybe I should be disappointed at
not passing but then I never did set up a new group of users nor think about
cross permissions at different supervisory levels and other absolute minimum
requirements. If there were no test questions for things so trivial ... ;)

--
Before the Gaza massacre Israel was given the benefit of the doubt.
With Gaza Israel removed all doubt.
-- The Iron Webmaster, 4237
http://www.giwersworld.org/palestine/answers.phtml a9
Tue Mar 2 00:19:27 EST 2010
David Kerber
2010-03-02 13:11:12 UTC
Permalink
In article <4b8ca6de$0$5119$***@unlimited.newshosting.com>, jull43
@tampabay.rr.com says...

...

> Lots of things are always on that are not necessarily used. Look
for mysqld
> for example. These services are turned on for whatever your dozens of users
> might have in mind. These distros do not have home users in mind.

That philosophy makes sense for server software like mysql, ftpd, etc.
It doesn't make sense for bluetooth, which is tied to hardware and is
very short range even when the hardware is installed.

D
Matt Giwer
2010-03-03 05:14:41 UTC
Permalink
On 03/02/2010 08:11 AM, David Kerber wrote:
> In article<4b8ca6de$0$5119$***@unlimited.newshosting.com>, jull43
> @tampabay.rr.com says...
> ....
>> Lots of things are always on that are not necessarily used. Look
> for mysqld
>> for example. These services are turned on for whatever your dozens of users
>> might have in mind. These distros do not have home users in mind.

> That philosophy makes sense for server software like mysql, ftpd, etc.
> It doesn't make sense for bluetooth, which is tied to hardware and is
> very short range even when the hardware is installed.

Please explain the sense of having a bluetooth driver loaded when bluetooth
is not used.

--
The threshold of atrocity is 6,000,000 - 1.
The threshold of atrocity is six million minus one.
-- The Iron Webmaster, 4235
http://www.giwersworld.org/antisem/ Antisemitism a10
Wed Mar 3 00:12:06 EST 2010
David Kerber
2010-03-03 15:00:21 UTC
Permalink
In article <4b8df04a$0$4975$***@unlimited.newshosting.com>, jull43
@tampabay.rr.com says...
>
> On 03/02/2010 08:11 AM, David Kerber wrote:
> > In article<4b8ca6de$0$5119$***@unlimited.newshosting.com>, jull43
> > @tampabay.rr.com says...
> > ....
> >> Lots of things are always on that are not necessarily used. Look
> > for mysqld
> >> for example. These services are turned on for whatever your dozens of users
> >> might have in mind. These distros do not have home users in mind.
>
> > That philosophy makes sense for server software like mysql, ftpd, etc.
> > It doesn't make sense for bluetooth, which is tied to hardware and is
> > very short range even when the hardware is installed.
>
> Please explain the sense of having a bluetooth driver loaded when bluetooth
> is not used.

None. That's what I've been trying to say...

D
Darren Salt
2010-03-05 19:31:55 UTC
Permalink
[Followups trimmed]

I demand that David Kerber may or may not have written...

> In article <4b8ca6de$0$5119$***@unlimited.newshosting.com>, jull43
> @tampabay.rr.com says...
>> Lots of things are always on that are not necessarily used. Look for
>> mysqld for example. These services are turned on for whatever your dozens
>> of users might have in mind. These distros do not have home users in mind.

> That philosophy makes sense for server software like mysql, ftpd, etc. It
> doesn't make sense for bluetooth, which is tied to hardware and is very
> short range even when the hardware is installed.

OTOH, USB Bluetooth adapters are fairly easy to acquire, IME. I'm sure that
if the relevant packages weren't installed by default, we'd be seeing exactly
the opposite complaint from somebody else.

Anyway, my guess is that, in the case in question, installation of
recommended packages hasn't been disabled; and the Bluetooth packages have
been pulled in because of that.

--
| Darren Salt | linux at youmustbejoking | nr. Ashington, | Doon
| using Debian GNU/Linux | or ds ,demon,co,uk | Northumberland | Army
| + It's 1984.

Illiterate? Write for a free brochure!
Continue reading on narkive:
Loading...